The teaching methodology to be followed is oriented to the student's learning of the subject on an ongoing basis. This process is based on the realization of three types of activities that will be developed throughout the course: theory lectures, case studies and laboratory practicum.

• Theory lectures: the teacher will provide information on the knowledge of the subject and on strategies to acquire, expand and organize this knowledge. The active participation of the students during these sessions will be encouraged, for example by raising discussions in those points that have a higher conceptual load.
• Case studies: students will have to actively participate to consolidate the knowledge acquired by solving, presenting and discussing problems and case studies. The transversal competences T01, T03 and T05 will be evaluated in the papers presented in the case studies by carrying out a critical analysis of the work done by each member of the team and the total work presented. This part will have a 5% to the grade of each of the case studies.
• Laboratory practicum. Students will work as a group in the development of laboratory practicum related to the use of computer and robotic tools.

The evaluation of the subject will be done progressively and continuously throughout the semester for each block.

a) Blocks evaluation process.

For each of the three blocks that make the subject, the teacher will propose a series of activities (case studies and practices with a computer). The student, conducted by the teacher, will have to work on the development of the activities. Likewise, they must present them in the form and on the date indicated by the teacher and make an oral defense.

The final mark will be calculated as follows

FinalMark = 40% * MarkBlock1 + 40% * MarkBlock2 + 20% * MarkBlock3

To pass the course, you must obtain a minimum grade of 5 as a result of the calculation of final grade (FinalMark). To apply the FinalMark formula it will be necessary to obtain a minimum grade of 3.5 in all grades of the blocks, i.e. each of the grades MarkBlock1, MarkBlock2 and MarkBlock3 must be greater than or equal to 3.5. Therefore, if a MarkBlock is graded with a grade lower than the one indicated above, the subject cannot be passed.

If a student does not reach the minimum grade of 3.5 in any of the MarkBlock and for this reason does not pass the course, the final grade will be a maximum of 4.5, i.e. it will be equal to the value of the weighted average if FinalMark is less than 4.5 or 4.5 if it is higher.

b) Programming evaluation activities

The scheduling of the evaluation activities will be given on the first day of the subject and will be made public through the Virtual Campus (Moodle) and on the website of the Engineering School, in the exams section.

c) Make-up process

To pass the course, students must obtain a minimum grade of 3.5 out of 10 in each assessment block. Any assessment block that does not reach this minimum grade will be subject to a specific recovery process during the semester, as determined by the instructor. This process may include a resubmission of the assignment, a new individual oral presentation, or other equivalent assessment activities. Recovery applies exclusively to assessment blocks that have not achieved the minimum grade of 3.5 and is intended to allow students to demonstrate attainment of the corresponding learning outcomes. Therefore, there is no comprehensive end-of-semester resit or recovery assessment for the course as a whole. Once the minimum grade of 3.5 has been achieved in all assessment blocks, the block grades may be compensated according to the weights established in the assessment system.

d) Procedure for review of qualifications

For each evaluation activity, a place, date and time of revision in which the student can review the activity with the teacher will be indicated. In this context, claims may be made on the activity grade, which will be evaluated by the faculty responsible for the subject. If the student does not show up for this revision, this activity will not be reviewed later.

e) Qualifications

The final grade of the subject will be calculated according to the percentages mentioned in section a)of this point. Keep in mind that:

• Honor plates. Granting a grade of honor registration is only the decision of the faculty responsible for the subject. The regulations of the UAB indicate that MH can only be granted to students who have obtained a final grade equal to or greater than 9.00.
• Not evaluable. A student who has not submitted to any Activity will be considered \"non-evaluable\". In any other case, the evaluation criteria detailed above are followed.

f) Irregularities by the student, copy and plagiarism

Without prejudice to other disciplinary measures deemed appropriate, the irregularities committed by the student that may lead to a variation of the grade of an evaluation act will be scored with a zero. Therefore, copying, plagiarism, cheating, letting copy, etc. in any of the evaluation activities will involve suspending it with a zero. If it is necessary to pass any of these evaluation activities to pass the subject, this subject will be suspended directly, without the opportunity to recover it in the same course.

g) Evaluation of repeating students

No mark is saved from one course for the next. Repeating students follow the same evaluation standards asany other student.

h) Use of Artificial Intelligence tools

Prohibited use: In this course, the use of Artificial Intelligence (AI) technologies is not allowed at any stage. Any work that includes AI-generated content will be considered a breach of academic integrity and may result in a partial or total penalty in the activity’s grade, or more severe sanctions in serious cases.